#Netgear genie smart setup n600 how to
#Netgear genie smart setup n600 full
#Netgear genie smart setup n600 mac
#Netgear genie smart setup n600 windows

It provides additional functionality on a Windows system. NETGEAR Genie is an official program developed by Netgear for owners of certain routers produced by the company. I am not sure if the 3400 has a repeater mode, but I advise against it, often it will not support WPA2, and at best you end up with half of your wifi throughput when going through a repeater.Official tool offering router owners access to filesharing, streaming, configuration, parental controls and other NETGEAR settings.

#Netgear genie smart setup n600 full

Once applied, you should be able to just connect the router in a LAN to LAN fashion, and still retain full access to the netgear router settings as well as its features additional features. Once that cable is disconnected, you can then head to the Advanced tab, and then Setup, then go to LAN Setup, and then change the local IP of the router to an address in the same range as your main router, e.g., if the main router is 192.168.1.1, then change the netgear router to something like 192.168.1.64 or any other IP in the range after that, also uncheck Use Router as DHCP Server. If you do not have the option for wireless AP, then you will have to do it manually.įirst step will be to disconnect the any cable leading to the WAN port (so the genie firmware stuff will allow you to change the local IP of the router to an address in the same IP range as the main router, as by default, it will automatically change its IP to a different range if behind another router, e.g., if the main router is 192.168.1.1, then the netgear will automatically switch to 10.0.0.1).

To configure the router further (in case you want to change any settings in the future, you will have to head to your main router and look for whatever IP address it assigned the netgear router, then head to that address to get back to the netgear config page. Once enabled, it will use the WAN port as a LAN port and set everything up for you. How do we add the static address to the table and how do we give it an acceptable static address?

#Netgear genie smart setup n600 mac

Recall that you will also have to set the N600 static address in the Xfinity static table, which will require the MAC address of the N600 (it is on a sticker on the back or bottom). Attach the N600 to the XFinity LAN port to LAN port with the Ethernet cable (or powerline adapters, and get a good set of adapters). To set the N600 to AP mode, just turn off DHCP, give the N600 a static address that is in the network range but outside the Xfinity DHCP range, give the N600 a different non-overlapping radio channel (selecting from 1, 6, and 11), use the same SSID, same wireless security type and same passkey. If that is impossible, you can use a pair of powerline adapters to get the signal to the N600 and still run in AP mode.

You will get far better results if you can run a cable up to the N600 and run it in AP mode. If is not difficult and you actually learn how your network functions.Īnd most people actually want to be able to share all devices on one network (printers) and exchange data between all computers two benefits of a single network. I would still recommend a unified network with multiple wireless radios. For most users a single network is a better answer.

#Netgear genie smart setup n600 how to

You can set it up as a second network, but just because you don't want to spend the time to learn how to make it part of a single network does not make it a good solution. I have used this second network for devices that I donot really care like internet streaming etc. My original network router is a Verizon and somehow I am getting a much better reception on my original network as well. It is going to be an unprotected network but easily usable if you are not worried about someone hacking your network. You should have another network called 'Netgear' showing up in your available set of Wifi networks. Once reset, connect to your Xfinity router using Ethernet cables. Rest the N600 by pressing the small button in the back. Not sure about all the technical lingo here but my solution was simple.